Power training and indoor trainers for cyclists simply belong together. The pure efficiency and controlled environment of indoor training partners amazingly well with precise training based on specific, targeted power numbers. Accurate power measurement and controlled smart trainers have taken this to new levels.
Because more and more people are now training indoors with their bicycle power meters, we are seeing significant improvements in the effectiveness of indoor training.
But there’s always a catch.
Training indoors with precise performance numbers can have some negative effects on your training. The introduction of clear training targets measured by watts has brought about some bad training habits, and they’re often disguised as the desire to improve performance as we focus on increasing just one number: average watts.
Here are two ways to look at indoor power training differently to improve your results.
Power vs. Duration
The introduction of power to indoor training has created a focus on “more power” that can be detrimental to long-term improvement performance. I often see athletes constantly striving for more power (increased watts) because they think this is the key to breakthrough during base training. They often repeat similar aerobic workouts in their pursuit to track their improvement by targeting higher power numbers alone. This obsession with power leads to problems with training focus and the need to constantly increase power, while forgetting completely about increasing power duration and fatigue resistance.
Change your thinking this winter. Focus more on power duration instead of pure power output.
Here’s a simple example. Say you do a lot of 2 x 20 minutes at tempo, sweet spot, or FTP training levels. This probably means you’re trying to get more watts each session, often turning tempo and sweet spot work into FTP intervals. I recommend that you focus more on increasing your time in those zones and let the power come up more naturally as you grow more fit. Instead of doing each workout a few watts higher, progressively expand the duration of your time in that zones.
You could start at 2 x 15 minutes of SST and progress to 2 x 20 minutes and then 3 x 15 minutes, which leads to 3 x 20 minutes of SST. I progress my athletes incrementally (often 1- to 2-minute increments) over the course of their base training, but there’s no reason to sit stagnant; I rarely plan more than three workouts at the same time length before increasing the time demand. Just remember that your power numbers will come up as the time increases, so you’ll need to test and monitor other data to gradually move up your power targets.
Why try this? Results! Increasing your power duration/fatigue resistance is more likely to improve your results than adding a few more watts of pure power in the base training phase. How many times have you made the break and gotten into the lead pack only to be dropped or be unable to hold? You had the power, but you couldn’t sustain it. It’s time to change that.
Power vs. Normalized Power
The trainer supplies an excellent basis for doing steady-state intervals as part of winter base training, but over time this can reduce your ability to produce power in a non-steady state. This can be viewed as actual power vs. normalized power. Too much steady state will reduce the rider's ability to transition back to the road come spring.
Change some of your intensive aerobic efforts (tempo and SST) to be “over-under” style. Here are a few ways to do this. Let’s say you have built up to 2 x 15 minutes of sweet spot training (SST), then start adding 30-second bursts at 110% of threshold every 3–5 minutes. This will produce some additional neuromuscular and cardiovascular demand. This “over-under” style more mimics actual road performance.
Once you've done a few of those, try doing some micro intervals, such as 4 x 10 minutes of 15 seconds hard followed by 15 seconds easy. Micro intervals will step up the neuromuscular demand even more and help prepare you for the transition back to the road.
Power vs. High Intensity
The trainer is hard enough, and doing high-intensity workouts on this torture device can be physically and mentally challenging. As a result, athletes tend to stay focused on aerobic efforts ranging from active recovery to intensive aerobic efforts such as SST and threshold work. The problem is that this approach neglects the anaerobic energy system and allows for its (often significant) decline. This decline will need more training focus when you return to the road in spring.
Add some high-intensity interval training (HIIT) to your training. HIIT is a hot topic right now, and there's plenty of information on the internet. For cyclists with less than six hours a week to train, I think full HIIT can be a good solution, but if you have more time than that (let’s say 8-10 hours), taking a more traditional approach will generally yield better long-term results.
That being said, adding HIIT to your training is a very helpful way to maintain your anaerobic system and maybe even improve it. There are plenty of types of HIIT out there, but I recommend a very intensive approach: true max efforts.
After the completion of at least 4-6 weeks of base training, try adding a HIIT day once every 10-14 days. A HIIT day example is 5 x 40- to 60-second max efforts with a soft pedaling recovery of 8-12 minutes (that's not a typo) to really allow your body to recover. Each target is max, and your legs should be stone when you are done. Make sure you do these after a rest day, and always warm up and cool down well. This intensive effort will drive both and anaerobic and aerobic response if you do them hard enough.
Power vs. Cadence
Power training is exactly what it sounds like: training by power. However, this has led to such a focus on output numbers of average power that I see more and more athletes not using their indoor training time to work on neuromuscular manipulation to increase cardiovascular load while potentially improving efficiency.
Start using more of your available data to track and encourage the introduction of efficiency drills into your training. I have my athletes focus on two types of drills during their base build:
1. Fast Pedaling
This is the simplest of all the drills, but I add a twist. I suggest doing fast pedaling drills 2-3 times a week as 10 x 1 minute with 1 minute of rest, but I like to break them up by doing 5 x 1 minute just after warming up (before the actual workout effort), then completing the final 5 x 1 minute after the workout effort (just before cooling down). We want to get cadence above 125 rpm for the minute, to not focus on power, and to focus on spinning without bouncing.
2. Over Fast Pedaling
This is a slightly more complex drill (I call it “rate coding pedaling intervals”), but it’s very effective. Just like the fast pedaling drill above, these are 10 x 1 minute, but you need to start them in a mid-range gear, get your fast pedal up to max for 30 seconds, then shift into one easier gear, spin fast for 15 seconds, and shift again to one easier gear for the final 15 seconds. This fast pedal format will teach you to “over-spin,” as each gear shift will help you spin faster than you thought possible and help improve your neural muscular pathing and performance.
The winter is a great time to focus your training and maximize your returns by using a trainer. Make sure you have a great training plan!
About the Author
Along with co-founding BaseCamp and Velocious Cycling Adventures, Tim Cusick is the TrainingPeaks WKO product leader, specializing in data analytics and performance metrics for endurance athletes. Tim is a USAC coach with years of experience working with both road and mountain bike cycling professionals around the world, including Amber Neben, Emma Grant, and Rebecca Rusch.